Can I Insert A Half Space Between Characters In Word Doc
Can I Insert A Half Space Between Characters In Word Documents
How To Insert Space Between Lines In Word

Nonbreaking spaces are special characters that keep words or individual characters from separating at line breaks. Nonbreaking spaces are particularly useful between ellipsis points. However, you can use them between any words or characters that you want to stay together. Thin spaces are a typographic device that allows you add a bit of space between elements of a document. There are no thin spaces available in Word (as separate characters), but you can create the same effect produced by thin spaces by using the ideas presented in this tip.

When working with a word document, other than changing the paragraph and line spacing, you also can change the spacing between letters and words. You can change the letter spacing in two ways: Expanded or Condensed. Please see the steps below for details:

Step 1: Select the contents you want to increase (or decrease) the letter spacing;

Step 2: Click the 'Home' tab from the ribbon;

Step 3: Click the Font Dialog Box Launcher in the corner of the 'Font' section;

Step 4: Click the 'Advanced' tab in the 'Font' dialog box;

Step 5: In the 'Spacing' box, select 'Expanded' if you want to increase the spacing between letters, or select 'Condensed' if you want to decrease the spacing, then type the value you want to expand or condense.

Step 6: Click 'OK' at the bottom to finish. The following is the comparison when the spacing is expanded to 1.5 pt.

Please refer to how to remove extra spaces in word to change the spacing between words only.

Step 7: The following is the results when the spacing is condensed with 80% scale.

It doesn’t take an experienced designer to say what’s wrong with this overused Internet photo:

The text is viciously close to the logo.

Ah, much better now. But if the owner is a trained therapist, we have another problem. It goes by…

Kerning:

a process of adjusting the spacing between characters in a proportional font, usually to achieve a visually pleasing result.

What Is Kerning

The more the text becomes a point of focus, the more our eyes perceive small imperfections in it. And one of the most common imperfections often lies in the space between letters, or font kerning.

The key word here is “perceive”. If you were to simply set an equal size of a blank space between all letters in the word, that wouldn’t do the trick. See for yourself:

Now if we apply kerning, your type will be perceived as more balanced and legible, even though the space between letters, geometrically speaking, is distributed unequally. In typography, it’s sometimes called horizontal rhythm.

Every font has a unique rhythm to it, and key factors to the rhythm are:

letters—every letter has a unique visual footprint in the word
elements—serifs, line weight, and line length can significantly alter the size of the same letter
pairs—the interplay between two adjacent letters is unique to every font

Letters

There are 5 types of letters:

Rectangular: M, H, N – have vertical elements on both sides
Rounded: O
Half-rounded: B, D
Half-Opened: L, E, C, K, J
Opened: X, T, W

If all the letters were rectangular, we could actually use the equal space approach:

However, as soon as combinations of different letter types come into play, we need to do some tweaking:

Typically, the space between rectangular characters will be the widest, while the characters with an open shape will require less of it.

Elements

There are countless elements in every typeface that make any letter unique. And they all have names! Descenders, hairlines, loops, serifs, terminals… The angle of the letter, the line weight etc.–everything can contribute to the way we perceive it.

Compare these two words in different fonts:

The dynamic between the first two characters “I” and “n” is completely different in both cases. Due to serifs and the overall angle, the letter “I” falls out in the former case. If we wanted to improve visual perception and readability we would have to bring it closer.

Pairs

Essentially, every ready-to-use font is a set of thousands of letter combinations or kerning pairs. Font designers try to anticipate every pair possible, and most of the time, that’s enough. For web fonts and word editors… However, certain pairs are always troublesome in almost every font, especially in larger sizes. Which means you almost always are going to have problems with those:

How To Kern

There is so much geometry that goes into kerning, but we’ll leave that to font designers. In this article, we’ll use a simple kerning technique: trios.

This is the word we’re going to kern:

Step 1. Let’s find the most complex pair of letters and adjust the spacing between them:

The space between two characters should not be too wide that they fall apart and not too narrow that they glue.

The kerning of this pair will determine the rest of the horizontal rhythm. Being one of the complex ones, it usually will have the least space between the two letters compared to the other pairs.

Step 2. Now we add another character adjacent to our base AT pair. Let’s take “I”

Step 3. Let’s again form the next trio of characters, two of which we’ve already kerned.

Step 4. By working with three characters at a time, we eventually kern the whole word

When to Kern

There may be circumstances when people don’t need kerning.

However, more often than not we need it. Kerning affects both readability and perception. Proper kerning is like proper interface design – if it’s done well, you don’t even notice it. If, however, something is off…

How to insert space between lines in word

The staggering amount of unfortunate “click” kernings out there makes me think of some conspiracy theory…

It’s not just about dirty jokes, though. Often reading badly kerned text may feel like torture:

The book can easily be reviewed badly just because its text had a bad kerning. The marketing ad may convert poorly for the same reason.

Yet, sometimes, unusual kerning can be intentional. Especially in logo design.

Take a Continental logo:

Here’s how it would look with proper kerning:

What Is Not Kerning

There’s another concept in typography very closely connected to kerning and it’s called tracking. Often people confuse them. This is tracking:

Increased tracking is very common with uppercase texts

After you’ve figured the space between individual characters, you can uniformly increase it or decrease it throughout the whole word. If you’ve done kerning properly, the visual perception will still be favorable.

However, tracking plays a huge part in how the word will be perceived.

I found these two logos on the Internet. While there is a slight difference in the fonts, the real difference lies in the space. It’s uniformly stretched in the second example. Feels like two different messages from the same company.

Just remember – that’s not kerning. That’s tracking. Here’s a useful visualization:

CSS Kerning

It’s harder to control kerning for websites than to control it in your design mockups. This is one of the many reasons why people prefer to use established fonts on the web rather than self-made.

Thankfully, we have a few CSS kerning parameters to control the typography on the web.

The first is font-kerning and it basically controls whether you want to use the built-in kerning pairs that the font-designer established for the web. In most cases, you use a default parameter auto.

These are available values:

font-kerning: auto; font-kerning: normal; font-kerning: none;

Sometimes you may find int useful to disable font kerning with css for a specific portion of your text:

<span>AV</span> The sims 3 compl

Can I Insert A Half Space Between Characters In Word